This page was exported from All The Latest MCTS Exam Questions And Answers For Free Share [ https://www.mctsdump.com ] Export date:Sat Nov 23 7:58:20 2024 / +0000 GMT ___________________________________________________ Title: [2016-NEW!] 300-370 Exam Questions with Free PDF and VCE Download From PassLeader (Question 16 – Question 30) --------------------------------------------------- Choosing PassLeader 300-370 exam dumps and passing 300-370 exam today! PassLeader just released the newest 300-370 study guide with 300-370 VCE dumps and 300-370 PDF dumps, which cover all new 300-370 exam questions updated recently. You can pass the 300-370 exam easily by learning PassLeader 300-370 practice tests! Welcome to choose the valid 300-370 dumps on passleader.com! keywords: 300-370 exam,70q 300-370 exam dumps,70q 300-370 exam questions,300-370 pdf dumps,300-370 practice test,300-370 vce dumps,300-370 study guide,300-370 braindumps,Troubleshooting Cisco Wireless Enterprise Networks Exam P.S. Download Free 300-370 PDF Dumps From Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpM3ZXaF9TdmZSeUU QUESTION 16Refer to the exhibit. Which statement about the join process of the access point is true? A.    The time on the controller is outside of the certificates validity time interval, so the join phase failed.B.    The AP moved from this controller to its primary controller.C.    The controller rejected most of the discovery requests from the AP because they were not received on the management interface subnet. The AP failed to join the controller.D.    The AP successfully joined the controller.E.    The AP failed to join because the self-signed certificate of the AP on the controller was not correct. Answer: C QUESTION 17Refer to the exhibit. An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can the engineer identify? A.    microwaveB.    DECT phoneC.    BluetoothD.    jammer Answer: A QUESTION 18An engineer has configured 802 1x for the network and all but one of the APs are passing authentication. Which configuration is causing the failure? A.    The AP has override global credentials checked.B.    The switch AAA credentials do not match what is configured on ISE.C.    The controller 802 1x supplicant credentials do not match what is configured on ISE.D.    EAP-FAST is configured on ISE for this AP. Answer: A QUESTION 19Refer to the exhibit. Which statement about the join process of the access point is true? A.    The time on the controller is outside of the certificates validity time interval, so the join phase failed.B.    The AP successfully joined the controller.C.    The AP moved from this controller to its primary controller.D.    The AP failed to join because the MAC address of the AP was not correct on the controller.E.    The controller rejected all discovery requests from the AP because they were not received on the management interface subnet. Answer: E QUESTION 20Some users are experiencing inconsistent performance on their mobile devices as they move throughout the building when browsing the Internet. Which feature provides a more consistent user experiences? A.    low RSSI checkB.    802.11rC.    RX-SOPD.    optimized roaming Answer: A QUESTION 21An AP will be deployed to an area where DHCP Option 43 is unavailable and the WLAN engineer is unable to have DNS modifications made to support this AP. Which two actions can enable the AP to join the WLC? (Choose two) A.    Issue the clear capwap private-config command in the AP console.B.    Pre-stage or prime the AP on the same Layer 2 VLAN as the WLC.C.    Issue the capwap ap ip default-gateway WLC IP address command in the AP console.D.    Issue the capwap ap ip address WLC IP address command in the AP console.E.    Issue the capwap ap controller ip address WLC IP address command in the AP console. Answer: AD QUESTION 22Refer to the exhibit. Which statement about the join process of the access point is true? A.    The AP failed to join because the self-signed certificate of the AP was not correct on the controller.B.    The time on the controller is outside of the certificates validity time interval so the join phase failed.C.    The AP moved from this controller to its primary controller.D.    The AP successfully joined the controller. Answer: B QUESTION 23A Wireless LAN Cisco engineer is troubleshooting 802. 11ac WLAN at customer site Doe to interferences with neighboring 802 11n networks the engineer must determine the current primary secondary channel allocation to enhance the current configuration. Channel 60 has been chosen by the customer as primary 20 MHz channel. Which combination determines the resulting primary 40 MHz and primary 80 MHZ channels? A.    primary 40 MHz channel 62, primary 80 MM: channel 58B.    primary 40 MHz channel 54, primary 80 MHz channel 58C.    primary 40 MHz channel 64, primary 80 MHz channel 60D.    primary 40 MHz channel 60, primary 80 MHz channel 56 Answer: A QUESTION 24A wireless engineer has completed the configuration of a new WLAN on the existing Cisco wireless infrastructure. During testing he found that the wireless client's authenticate and received the correct ip address from the switch, but they were not able to access any of the internal or external resources. Which action will resolve the issue? A.    Configure static ip addresses for the wireless clients.B.    Configure the default-router on the switch DHCP pool.C.    Configure option 82 on the switch DHCP pool.D.    Configure a dns-server on the switch DHCP pool. Answer: C QUESTION 25Which channel width is the maximum that can be obtained by bonding two 802.11 ac subchannels according to US regulations? A.    160 MHzB.    120 MHzC.    84 MHzD.    240 MHz Answer: A QUESTION 26Which statement about the usage of the debug command in a Cisco Unified Wireless Network is true? A.    Debug is enabled until manual shut off.B.    Debug is a message logging severity 7.C.    Debug is a restricted command and is not available in the AP CLI.D.    Debug is available on the WLC serial console and web interface. Answer: B QUESTION 27Two 5508 Wireless Lan Controllers are managing all Access Points throughout the network The WLCs are located in different locations to provide geographical redundancy A Mobility Group has been configured on both WLCs and has a UP status on both Controllers The APs m location A are statically configured to use Controller A as the Primary and Controller B as the Secondary If the WLC in location A goes offline, the APs successfully join the WLC m location B but they do not failover to their Primary configured Controller. What configuration task will fix this issue? A.    Change the AP Failover Priority to critical.B.    Enable AP Fallback globally on the WLC.C.    Configure the WLC in location A as Primary using the CAPWAP AP Controller IP Address command on all the location A Access Points.D.    Use DHCP Option 43 and specify WLC in location A as Primary. Answer: C QUESTION 28Refer to the exhibit. A mobile station in a factory contains an AP configured as a work group bridge that authenticates to a root AP using EAP-FAST. To be able to use the mobile station in further parts of the factory, another root AP is installed and also configured for EAP-FAST When the mobile station is attempting to roam to the other AP, it loses connection yet can still authenticate to the first one. What is the cause for the failed authentication on RAP2? A.    RAP1 is using a different authentication protocol than RAP2.B.    RAP2 has a different SSID than RAP1.C.    RAP1 is using a different encryption than RAP2.D.    The authentication usemame and password is different. Answer: A QUESTION 29Refer to the exhibit. A client reports being unable to log into the wireless network According to the output, which network information should be verified? A.    the Failed Attempts log on the authentication serverB.    that the AP has IP connectivity to the authentication serverC.    that the user has an account on the authentication serverD.    that the authentication and accounting configuration are correct Answer: B QUESTION 30ScenarioThe Big Engineering IT team has been working in the lab to do some testing of some new features the existing network won't support. They are AP Croups, AP Failover, and Local Web Auth. They have been having problems with all three features. In this test environment the controllers only support the Composite and Structural Engineering and Aerodynamic Engineering groups. All SSIDs should omit the department name. Refer to the exhibit. This is a diagram of the floor plan for the Big Engineering office and the distribution of the departments. The tables below show how the controllers have been configured. Note, not all menu items, text boxes, or radio buttons are active.When you review the configuration of the test network controller what needs to be changed to resolve the problems? (Choose four.) A.    Change the High Availability Primary Controller Management Interface IP addressB.    Remove the current WLANs and replace them with WLANs that have the same SSID names as on the AE-2504A controllerC.    Add the Local Net User names and passwordsD.    Change the Layer 2 security to none and Layer 3 Security to Web Policy for the CSE- Contractors WLANE.    Remove me current WLAN from the CSE-WLAN AP Group and add all three of the WLANs configured in the CSE-2504AF.    Add the CSE APs to the CSE-WLANs AP-Group Answer: BCDF Download the newest PassLeader 300-370 dumps from passleader.com now! 100% Pass Guarantee! 300-370 PDF dumps & 300-370 VCE dumps: http://www.passleader.com/300-370.html (70 Q&As) (New Questions Are 100% Available and Wrong Answers Have Been Corrected!) P.S. Free 300-370 PDF dumps download from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpM3ZXaF9TdmZSeUU --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2016-06-29 06:48:49 Post date GMT: 2016-06-29 06:48:49 Post modified date: 2016-06-29 06:48:49 Post modified date GMT: 2016-06-29 06:48:49 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com